Your Complete Plumbing Guide for Installing a Bathtub
Your Complete Plumbing Guide for Installing a Bathtub
Blog Article
Here below you'll find a lot of incredibly good answers on the subject of How to Install a Bathtub.
Installing a bathtub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a new one is also a moderately difficult job. If the old bathtub is readily easily accessible, the task can move quickly; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. Instead of employing a contractor to take control of a halfway-completed project, it is much better to think about employing one before you begin. Chances are you may require an expert plumber to make tube links.
This short article will certainly aid you mount a new tub in your washroom if you have actually already purchased a new tub and also do not require to transform the setup of your previous supply of water pipelines.
Your tools and material checklist ought to consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome as a result of the restricted accessibility that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the tap in position with the supplier given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the tub until the level reviews level.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water system and also check all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub as well as also examine the overflow outlet as well as the normal electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized a minimum of when as this will settle it into its final placement.
Getting ready for the Setup
To start with, the sustaining frame supplied with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, causing complications with moisture and feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the market. It is recommended to fit the floor tiles utilizing water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very focused on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you appreciated the entire post. So long as you appreciated our blog posting kindly don't forget to pass it around. Many thanks for going through it.
Perfect solution? Dial! Report this page